1-800-936-2819
1-800-936-2819
If a dispenser pours normally for single drinks but slows when two or more nozzles operate at once, the system is usually capacity- or supply-limited — not simply a mysterious “bad” pump. A pump that meets single-outlet demand can still be undersized for simultaneous draws, or inlet plumbing/filters/valves can restrict peak flow. Compare measured peak total demand to the installed pump's rated flow at your working head to decide.
Always quote the exact nameplate model and verify its published limits on the product page before diagnosing. Example Procon model pages you can use to confirm published values and to check photos for port size and integrated features:


Use these exact pages to confirm flows, pressure limits, port sizes and the presence of integrated strainers — photos on each product page help check a physical match to your installed unit.
(Images on the model pages assist verification; see the photos linked above for physical details.)
Pump ratings are conditional — they specify flow at particular head, speed and fluid conditions. A single nozzle draw may sit under that rating, but multiple simultaneous nozzles increase peak demand (the sum of each nozzle's target flow). If peak demand > pump rated flow at the working head, individual nozzle flows fall. Alternatively, the pump might be capable but upstream restrictions (small hoses, clogged strainer, low supply level) reduce delivered flow in-system.
| Fault | How it shows up | Measurement to prove it | Example (supported by product pages) |
|---|---|---|---|
| Undersized pump | Per-outlet flow declines whenever total open outlets increase; single-outlet flow near rated but total delivered cannot meet simultaneous demand | Total measured flow (LPH) with all outlets open < pump rated flow at working head | Two 180 LPH heads on a PROCON 141A060F11CA (180 LPH rating) — two-head demand 360 LPH > 180 LPH pump rating → undersized pump (see product page: PROCON 141A060F11CA). |
| Plumbing / supply restriction | Pump outlet pressure drops or inlet pressure collapses under load; cleaning strainers or increasing hose ID restores flow | Inlet/suction pressure plunge under simultaneous demand; cleaning strainer or upsizing hose increases delivered flow toward pump's rated value | A PROCON 144B240F11BA (725 LPH rating) installed with 1/8" tubing and a clogged strainer shows low delivered flow despite pump rated capacity; cleaning or re-piping improves flow (see product page: PROCON 144B240F11BA). |
Units note: we use LPH primarily and show GPH where the product record lists it.
| Time | Outlet A (LPH) | Outlet B (LPH) | Outlet C (LPH) | Total Demand (LPH) | Observed Total (LPH) |
|---|---|---|---|---|---|
| 10:00 | 180 | 0 | 0 | 180 | 175 |
| 10:10 | 180 | 180 | 0 | 360 | 220 |
| 10:12 | 180 | 180 | 180 | 540 | 300 |
Interpretation (hypothetical): single-outlet pours near 180 LPH; with two or three outlets open the machine delivers far less than the sum requested — either the pump cannot sustain the combined flow at system head or the supply/plumbing restricts the delivered flow.
Use the same log format with real values when you test your machine and then compare totals to the installed pump's published flow on its product page.
This worked example shows how a service tech converts nozzle data and system head into a required pump selection.
Given:
Procedure:
Practical note: If the pump product page lists a range (e.g., 240 GPH / 725 LPH for PROCON 144B240F11BA), confirm the port size, relief setting and mounting match your machine before ordering: PROCON 144B240F11BA.
A pressurized accumulator (air-charged bladder) can supply short surges without upsizing the pump. Use this when peaks are brief (a few seconds) and the average flow is within the pump capacity.
Sizing approach (illustrative):
Select a bladder tank whose usable liquid volume (not total vessel volume) exceeds Vsurge allowing for precharge and acceptable pressure drop. Usable volume depends on precharge and operating pressure band; as a rule of thumb, choose a tank with 2–4× the calculated Vsurge to allow for effective precharge settings and aging. In the example, a small 2–4 L tank typically covers the brief surge comfortably. Confirm with manufacturer sizing charts for final selection.
Accumulator tips:
Small-bore tubing creates large frictional pressure drops at modest flows. The numbers below are illustrative to show the effect of hose ID; label them as hypothetical unless you calculate with a friction chart or software for your exact fluid, temperature and roughness.
Illustrative comparison (hypothetical):
Practical action:
If cross-brand interchange claims are needed, convert specs (flow at head, port size, relief settings) and treat any crossovers as conditional until verified; do not assume a drop-in replacement without checking physical and performance fit.
Q: Can I increase pump speed to get more flow?
A: Only if the motor and pump are rated for the higher RPM. Check the pump's published min/max RPM and mechanical-power requirement on the product page before attempting speed changes.
Q: Will a larger pump harm valves or heads?
A: Higher capacity can increase system pressure. Verify valves, hoses and fixtures are rated for increased pressure and use a pressure-limiting device if needed.
Q: Is an accumulator useful?
A: Yes. A pressurized buffer can smooth short-duration peaks and delay the need for a larger pump when surges are brief.
Q: How to tell wear versus undersize?
A: If single-outlet steady flow is well below the pump's published single-outlet rating after cleaning strainers and confirming motor speed, the pump is likely worn and should be replaced. See the manufacturer troubleshooting and safety guidance for wear signs: PROCON troubleshooting and safety pages are useful references.
Have these ready: exact pump model nameplate and photos, measured single-outlet and simultaneous total flow (LPH), inlet and outlet pressures (psi) during single and multi-outlet draws, fluid type and temperature, hose IDs and lengths, strainer/filter condition, and electrical supply (V, Hz, motor RPM). These details let HDI recommend plumbing fixes, an accumulator or a properly rated Procon replacement.
Measure first, then change. Use the nameplate model to confirm published flow and pressure on the product page, log real peak simultaneous demand, and only replace the pump if measured requirements exceed the pump's published capability at your working head. Often the fastest, least expensive fix is correcting supply plumbing or cleaning strainers; sometimes a higher-capacity Procon pump is the right long-term solution.
{"one"=>"Seleccione 2 o 3 artículos para comparar", "other"=>"{{ count }} de 3 artículos seleccionados"}
Seleccione el primer artículo para comparar
Seleccione el segundo artículo para comparar
Seleccione el tercer elemento para comparar
Dejar un comentario